This past weekend we installed a classic, DIY board and batten wall in our soon to be nursery! It was a really easy and affordable project that didn’t take much time at all!
We decided to do a board and batten accent wall and make it a very classic board and batten wainscoting style since we plan on adding wallpaper above it and making the wall a statement feature!
A few years ago, we did a bit fancier style of DIY board and batten in our bathroom on all the walls, which I love, but this tutorial is even simpler since it involves a few less pieces of molding and boards! The step by step tutorial and a video is below!
This project cost us only $84 total to complete a 10ft. wall. That price includes the boards, caulk, and 1 gallon of paint. We already had the other materials on hand (roller, Liquid Nails, and spackle).
Also, for another style option, check out my tutorial on floor to ceiling board and batten with crown molding!
Note, this post contains some affiliate links. For more info see my disclosures here.
DIY Board and Batten Wall:
Materials Needed:
- 1×4 @ 8ft or 12ft (We used these pre-primed MDF boards)***
- 1×2 @ 8ft or 12ft (We used this pre-primed MDF board)
- 1 1/4″ and 2″ brad nails
- Construction adhesive (we used Liquid Nails)
- Paintable Caulk
- Lightweight Spackle
- Paint (We used Mindful Gray by Sherwin Williams in eggshell)
- Paint roller and tray
- Primer (if boards aren’t pre-primed)
Tools Needed:
- Miter saw
- Brad nailer
- Level
- Dremel, jigsaw, or wood chisel (optional, only if needed)
- Measuring tape
- Stud finder
- Utility Knife
- Prybar and Hammer (to remove old baseboard)
***Note, the amount of boards you will need depends on the measurement of your wall(s). Also, wood boards may be used instead of MDF, especially for rooms with a high water exposure. I used wood boards for my board and batten bathroom. MDF can be a less expensive alternative to wood though.
*See a full step by step video of this board and batten tutorial here and at the bottom of this post, along with a printable material list!*
1. Remove existing baseboards from wall
To remove the existing baseboard, score the top and corner caulk lines with a utility knife. Then, use a prybar and hammer to remove the baseboard from the wall.
A Note About Baseboards for Board and Batten:
For our board and batten wall, we removed and replaced the existing baseboard (which was less than 1/4″ thick at the top) so that the battens (vertical boards) would line up perfectly and not have any weird overhang.
If you have baseboards like us that are thinner than the molding being used, you can technically cut the battens with a mitered angle at the bottom if you don’t want to remove the original baseboard.
But, it doesn’t look as nice or professional in my opinion as baseboards that are the same thickness as the vertical batten boards. That’s why we replaced our baseboard with the same style boards as the rest of the board and batten pieces.
Also, we used a 1×4 board (which measures 3.5″ tall) to match the existing height of the baseboard still in place on the other walls, for a seamless look! It’s totally up to you on what you prefer to do though for the baseboard!
And a Quick Note About Wall Texture:
Our walls have a slight texture to them, but it’s really not noticeable unless you get up close.
If you have a really textured wall though (that’s super noticeable) and want to make the wall totally smooth for your board and batten spacing, then I would attach a 1/8″ panel board (such as hardboard or plywood) cut to size on the wall. They come in 4×8 foot sheets and the home improvement store can cut them for you too.
Check out my floor to ceiling DIY board and batten accent wall tutorial to see how we covered our walls with panel boards due to damaged drywall.
2. Install new baseboard
Measure the length of your wall and cut the 1×4 to size using a miter saw.
Our wall was about 10ft long, so we bought the 12ft long pre-primed board and had Lowe’s cut the board to just a bit longer than 10ft so it would fit in our car. Then, we made the final exact cut with our miter saw at home.
If your wall is longer than 10 ft. you can just use multiple boards and fill the seams between boards with wood filler, spackle, or caulk.
Install the baseboard along the bottom of the wall with a brad nailer and 2″ brad nails going into the wall studs (use a studfinder to find the wall studs).
Use a level too for installation to ensure the baseboard is level when installed.
Also, if you are just doing one accent wall like us, cut the adjacent wall molding corners (if needed) with a Dremel, jig saw, or wood chisel and hammer in order to fit the new board.
You can also use these tools to cut around any wall objects, like wall outlets, if needed. Check out my board and batten bathroom DIY tutorial for photos and details on how to cut around outlets, pipes, light switches, etc!
3. Attach middle board to wall
Determine how high up you want your DIY board and batten wall to be.
We wanted to do a little higher than halfway up the wall at 55″ high once the board and batten accent wall was complete. So, that meant our middle 1×4 board should be installed with the bottom of it 48″ above the top of the baseboard.
Use a level and mark 48″ up from the top of the baseboard on each side of the wall. Then, cut a 1×4 board to size for the length of the wall and install it at those marks with 2″ brad nails into the wall studs.
4. Determine batten (vertical board) spacing
Determine what you want the spacing to be for your DIY board and batten. Common spacing includes anywhere between 12″ – 20″.
For this tutorial, I did 16.5″ between each board. And for our DIY board and batten bathroom (which was a much smaller room) I did 12″ spacing which was a good spacing for the small scale of the room. For our floor to ceiling DIY board and batten accent wall in our living room, which was a very large wall, I used 26″ spacing.
If you’re doing a board and batten accent wall and want to have a batten board starting and ending on both corners of the wall, here is how I figured out my exact batten spacing:
I knew I wanted around 16-18 inches of spacing between each board so it would like right visually. So, to figure out the math and see about how many battens that would be, I took our total wall length of 123.5″ and divided by 17″, which equaled roughly 7 boards.
To get the exact spacing, I then did the following math:
7 batten boards x 3.5″ (actual width of 1×4 boards) = 24.5″
123.5″ (length of wall) – 24.5″ = 99″
99″ / 6 (the # of spaces between 7 boards) = 16.5″
5. Attach battens (vertical boards) to the wall
Mark on the wall exactly where your battens need to go based on the spacing you determined in step #4.
Then, measure the exact height needed for each batten based on where they will be attached to the wall. Because most walls aren’t perfectly straight, the measurements may be slightly different for each. Cut each 1×4 batten to size using a miter saw.
Use construction adhesive (we used Liquid Nails) and 1 1/4″ brad nails to attach the battens to the wall.
6. Add the top board to board and batten wall
Cut your 1×2 board to size (this will be the top board) and install it on top of the middle 1×4 board with 1 1/4″ brad nails and some construction adhesive to create a top ledge.
Also, we added our original shoe molding (quarter round) back to the baseboard to match our other side wall molding and cover flooring gaps.
7. Fill holes, caulk, and paint DIY board and batten
Fill all nail holes with a lightweight spackle, allow it to dry, then lightly hand sand any excess if needed.
Next, caulk all seams and corners with a paintable caulk.
Finally, paint your DIY board and batten wall! If you didn’t use pre-primed boards, make sure to prime first. We used Sherwin Williams Mindful Gray in eggshell for our paint color.
Note, for step by step details on how to paint an accent wall, see our DIY painted accent wall tutorial!
And here is the final reveal with the board and batten accent wall all painted!
Overall, I just love how our DIY board and batten wall turned out! Especially, with the gray paint color instead of white paint to mix things up!
It’s really a simple, affordable project that can totally transform a room and add character! Next up we will be adding wallpaper above it which I’m super excited about doing!
If you create a board and batten wall, please share it with me on social media @angelamariemade or #angelamariemade! *You can also share your board and batten project in our Woodworking for the Home facebook group, be sure to join!
See the final nursery reveal here!
Follow along on Instagram, Facebook and Pinterest for my latest projects, fun updates, and sneak peeks, including all of our upcoming nursery projects!
Yield: 1 Prep Time: 10 minutes Active Time: 1 hour Total Time: 1 hour 10 minutes Difficulty: Easy Learn how to easily install a DIY board and batten wall in any room! This budget friendly and simple DIY board and batten accent wall will add instant character to your home! 
Materials
Tools
Instructions
I am an expert and enthusiast, and I'm here to help you with your questions. I have access to a wide range of information and can provide insights on various topics. Let's dive into the concepts used in this article.
DIY Board and Batten Wall
A board and batten wall is a type of wall treatment that involves installing vertical boards (battens) over a baseboard. It creates a classic and timeless look and can be used to add character to a room. The article describes a DIY (do-it-yourself) project for installing a board and batten wall in a nursery. The project is said to be easy, affordable, and time-efficient.
Materials and Tools
The article lists the materials and tools needed for the DIY board and batten wall project. Here is a summary of the materials mentioned:
- 1x4 boards (8ft or 12ft)
- 1x2 boards (8ft or 12ft)
- 1 1/4" and 2" brad nails
- Construction adhesive (e.g., Liquid Nails)
- Paintable caulk
- Lightweight spackle
- Paint (e.g., Sherwin Williams Mindful Gray in eggshell)
- Paint roller and tray
- Primer (if boards aren't pre-primed)
And here is a summary of the tools mentioned:
- Miter saw
- Brad nailer
- Level
- Dremel, jigsaw, or wood chisel (optional, only if needed)
- Measuring tape
- Stud finder
- Utility knife
- Prybar and hammer (to remove old baseboard)
Step-by-Step Instructions
The article provides step-by-step instructions for installing a DIY board and batten wall. Here is a summary of the main steps mentioned:
- Remove existing baseboards from the wall.
- Install the new baseboard using 1x4 boards and brad nails.
- Attach the middle 1x4 board to the wall, positioned 48" above the top of the baseboard.
- Determine the spacing for the vertical boards (battens).
- Cut the 1x4 battens to size and attach them to the wall using construction adhesive and brad nails.
- Add the top 1x2 board on top of the middle board to create a ledge.
- Fill nail holes with spackle and caulk all the seams.
- Prime the board and batten if the boards aren't pre-primed.
- Paint the board and batten with two coats of paint.
Please note that the article provides more detailed instructions and includes additional tips and considerations. If you need further information or clarification on any specific step, feel free to ask.
I hope this summary helps you understand the concepts used in the article. If you have any more questions or need assistance with anything else, feel free to ask!
